Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 1340

Page: 1340 / 2018

DHCP Relay Commands

page 32-64

OmniSwitch 6250 CLI Reference Guide

November 2009

-> show ip udp relay destination 1776

Service Port

VLANs

-----------------+--------+----------------

A UDP Protocol

1776

Release History

Release 6.6.1; command was introduced.

Related Commands

MIB Objects

iphelperTable

iphelperService

iphelperVlan

iphelperxPropertiesTable

iphelperxPropertiesName

iphelperxPropertiesPort

output definitions

Service

The active UDP service name.

Port

The UDP service port number.

VLANs

The VLAN assigned to the UDP service port that will forward traffic
destined for that port. Use the

ip udp relay vlan

command to configure

this value.

show ip udp relay service

Displays current configuration for UDP services by service name or by
service port number.

show ip udp relay statistics

Displays the current statistics for each UDP port relay service.

«
...
1338
1339
1340
1341
1342
...
»

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OmniSwitch 6250

Reviews:

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 1340 / 2018

Search results

Summary of Contents for OmniSwitch 6250

Reviews: