Home
/
Alcatel-Lucent
/
OmniSwitch 6250
/
Cli Reference Manual

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 775 / 2018

Share

Page: 775 / 2018

Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 775

Port Mobility Commands

OmniSwitch 6250 CLI Reference Guide

November 2009

page 21-7

Examples

-> vlan 10 dhcp port 3/1

-> van 20 dhcp port 4/1-16

-> vlan 30 dhcp port 5/1-32 6/5-10 8/7-22

-> vlan 10 no dhcp port 3/1

-> vlan 20 no dhcp port 4/1-16

Release History

Release 6.6.1; command was introduced.

Related Commands

MIB Objects

vDhcpPortRuleTable

vDhcpPortRuleIfIndex

vDhcpPortRuleVlanId

vDhcpPortRuleStatus

vlan dhcp mac

Defines a DHCP MAC address rule for an existing VLAN. Mobile ports
that receive DHCP frames with a source MAC address that matches the
address specified by this rule are temporarily assigned to the VLAN.

vlan dhcp mac range

Defines a DHCP MAC address range rule for an existing VLAN.
Mobile ports that receive DHCP frames with a source MAC address that
falls within the range specified by this rule are temporarily assigned to
the VLAN.

vlan dhcp generic

Defines a generic DHCP rule for an existing VLAN. Mobile ports that
receive DHCP frames that do not match other DHCP rules are tempo-
rarily assigned to the VLAN.

Displays existing VLANs.

show vlan rules

Displays rules defined for VLANs.

«
...
773
774
775
776
777
...
»

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments