Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 395

Page: 395 / 2018

802.1AB Commands

OmniSwitch 6250 CLI Reference Guide

November 2009

page 13-3

lldp transmit hold-multiplier

Sets the transmit hold multiplier value, which is used to calculate the Time To Live TLV.

lldp transmit hold-multiplier num

Syntax Definitions

num

The transmit hold multiplier value. The valid range is 2-10.

Defaults

Platforms Supported

OmniSwitch 6250

Usage Guidelines

•

The LLDP protocol must be enabled before using this command.

•

The Time To Live is a multiple of transmit interval and transmit hold multiplier.

Examples

-> lldp transmit hold-multiplier 6

Release History

Release 6.6.1; command was introduced.

Related Commands

MIB Objects

lldpConfiguration

lldpMessageTxHoldMultiplier

parameter

default

num

lldp transmit interval

Sets the transmit time interval for LLDPDUs.

show lldp local -system

Displays local system information.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OmniSwitch 6250

Reviews:

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 395 / 2018

Search results

Summary of Contents for OmniSwitch 6250

Reviews: