Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 197

Page: 197 / 2018

Session Management Commands

OmniSwitch 6250 CLI Reference Guide

November 2009

page 6-37

show more

Shows the enable status of the more mode along with the number of lines specified for the screen display.

show more

Syntax Definitions

N/A

Defaults

N/A

Platforms Supported

OmniSwitch 6250

Usage Guidelines

•

This command shows the enable status of the

more

mode.

•

The number of lines displayed is the value set with the

more size

command.

Examples

-> show more

The more feature is enabled and the number of line is set to 12

Release History

Release 6.6.1; command was introduced.

Related Commands

MIB Objects

SystemServices

systemServicesArg1

systemServicesAction

more

Enables the more mode for your console screen display.

more size

Specifies the number of lines that your console screen will display.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OmniSwitch 6250

Reviews:

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 197 / 2018

Search results

Summary of Contents for OmniSwitch 6250

Reviews: