manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 842 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 842

GVRP Commands

page 23-16

OmniSwitch 6250 CLI Reference Guide

November 2009

Related Commands

MIB Objects

alaGvrpPortConfigTable

alaGvrpPortConfigRestrictedApplicantBitmap

alaGvrpPortConfigAllowApplicantBitmap

alaGvrpPortConfigApplicantBitmap

gvrp applicant

Configures the applicant mode for the switch port.

show gvrp configuration 
linkagg/port

Displays the GVRP configuration for a specific port or an aggregate of 
ports.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments