manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 629 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 629

OmniSwitch 6250 CLI Reference Guide

November 2009

page 18-1

18   Source Learning

Commands

Source Learning is responsible for creating, updating, and deleting source and destination MAC Address 
entries in the MAC Address Table. This chapter includes descriptions of Source Learning commands used 
to create or delete static MAC addresses, define the aging time value for static and dynamically learned 
MAC addresses, and display MAC Address Table entries and statistics.

MIB information for Source Learning commands is as follows:

Filename

:

AlcatelInd1MacAddress.mib

Module

:

ALCATEL-IND1-MAC-ADDRESS-MIB

A summary of the available commands is listed here:

mac-address-table
mac-address-table static-multicast
mac-address-table aging-time
source-learning
show mac-address-table
show mac-address-table static-multicast
show mac-address-table count
show mac-address-table aging-time
show source-learning

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments