manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 648 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 648

Source Learning Commands

page 18-20

OmniSwitch 6250 CLI Reference Guide

November 2009

Release History

Release 6.6.1; command was introduced

Related Commands

Related MIB Objects

slMacAddressTable

slMacLearningControlTable

slMacLearningControlEntry

slMacLearningControlStatus 

output definitions

port

The slot/port number for a switch port or a link aggregate ID number. If 
the interface is a link aggregate ID, zero is displayed as the slot number 
(e.g., 0/29).

source-learning

The source learning status of the port or link aggregate (

enabled

 or 

disabled

). Configured through the 

source-learning

 command.

source-learning

Configures the status of source MAC address learning on a single 
port, a range of ports or on a link aggregate of ports.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments