Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 1460

Page: 1460 / 2018

QoS Commands

page 38-32

OmniSwitch CLI Reference Guide

November 2009

Related Commands

MIB Objects

alaQoSConfigTable

alaQoSConfigFlush

qos revert

Deletes any QoS configuration that has not been applied to the configu-
ration through the

qos apply

command.

qos apply

Applies configured global QoS and policy settings to the current config-
uration (changes will be active and stored in flash).

policy server flush

Removes all cached LDAP policy data from the switch.

«
...
1458
1459
1460
1461
1462
...
»

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OmniSwitch 6250

Reviews:

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 1460 / 2018

Search results

Summary of Contents for OmniSwitch 6250

Reviews: