Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 1683

Page: 1683 / 2018

QoS Policy Commands

OmniSwitch CLI Reference Guide

November 2009

page 39-187

Release History

Release 6.6.1; command was introduced.

Related Commands

MIB Objects

alaQoSMACGroupsTable

alaQoSMACGroupsName

alaQoSMACGroupsSource

alaQoSAppliedMACGroupsTable

alaQoSAppliedMACGroupsName

alaQoSAppliedMACGroupsSource

alaQoSMACGroupTable

alaQoSMACGroupMacAddr

alaQoSMACGroupMacMask

alaQoSAppliedMACGroupTable

alaQoSAppliedMACGroupMacAddr

alaQoSAppliedMACGroupMacMask

output definitions

Group Name

The name of the port group, configured through the

policy mac group

command.

From

The origin of the MAC group:

cli

indicates that the entry was config-

ured on the switch;

ldap

indicates the entry was configured through

PolicyView.

Entries

The MAC addresses associated with the group.

policy mac group

Configures policy MAC groups.

«
...
1681
1682
1683
1684
1685
...
»

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OmniSwitch 6250

Reviews:

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 1683 / 2018

Search results

Summary of Contents for OmniSwitch 6250

Reviews: