manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 37 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 37

CMM Commands

OmniSwitch 6250 CLI Reference Guide

November 2009

page 1-5

•

If the switch is a part of a stacked configuration, using this command synchronizes the working direc-
tories of all the switches in the stack to the working directory of the primary CMM switch.

Examples

-> reload working rollback-timeout 5

-> reload working no rollback-timeout

-> reload working no rollback-timeout in 50

-> reload working rollback-timeout 10 at 12:50

Release History

Release 6.6.1; command was introduced. 

Related Commands

MIB Objects

chasControlModuleTable

csEntPhysicalIndex

chasControlActivateTimeout

reload

Reboots the CMM to its startup software configuration.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments