manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 801 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 801

OmniSwitch 6250 CLI Reference Guide

November 2009

page 22-1

22   VLAN Management

Commands

VLAN management software handles VLAN configuration and the reporting of VLAN configuration 
changes to other switch tasks. A VLAN defines a broadcast domain that contains physical ports and can 
span across multiple switches. All switches contain a default VLAN 1. Physical switch ports are initially 
assigned to VLAN 1 until they are statically or dynamically assigned to other VLANs. 

This chapter includes descriptions of VLAN management commands used to create, modify or remove 
VLANs. These commands allow you to enable or disable Spanning Tree Protocol (STP) and Authentica-
tion on a VLAN, add or remove virtual router interfaces, statically assign physical switch ports to a default 
VLAN, and display VLAN configuration information. 

The VLAN management commands comply with RFC 2674.

MIB information is as follows:

Filename

:

AlcatelIND1VlanManager.mib

Module

:

ALCATEL-IND1-VLAN-MGR-MIB

A summary of the available commands is listed here: 

vlan
vlan stp
vlan mobile-tag
vlan authentication
vlan port default
vlan source-learning
show vlan
show vlan port
show vlan router mac status
show vlan gvrp
show vlan ipmvlan

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments