Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 50

Page: 50 / 2018

CMM Commands

page 1-18

OmniSwitch 6250 CLI Reference Guide

November 2009

show microcode

Displays microcode versions installed on the switch.

show microcode [working | certified | loaded]

Syntax Definitions

working

Specifies the switch’s working directory; only microcode information
from the working directory will be displayed.

certified

Specifies the switch’s certified directory; only microcode information
from the certified directory will be displayed.

loaded

Specifies that only loaded (i.e., currently-active) microcode versions
will be displayed. Idle microcode versions will not be displayed.

Defaults

N/A

Platforms Supported

OmniSwitch 6250

Usage Guidelines

•

If no additional parameters are entered (i.e.,

working

certified

, or

loaded

), microcode information for

the running configuration will be displayed.

•

This command can also be used on the secondary CMM.

Examples

-> show microcode

Package Release Size Description

-----------------+---------------+--------+-----------------------------------

Jbase.img 6.1.1.403.R01 10520989 Alcatel-Lucent Base Software

Jos.img 6.1.1.403.R01 1828255 Alcatel-Lucent OS

Jadvrout.img 6.1.1.403.R01 1359435 Alcatel-Lucent Advanced Routing

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OmniSwitch 6250

Reviews:

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 50 / 2018

Search results

Summary of Contents for OmniSwitch 6250

Reviews: