Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 1571

Page: 1571 / 2018

QoS Policy Commands

OmniSwitch CLI Reference Guide

November 2009

page 39-75

policy condition icmptype

Configures an ICMP type value to use for traffic classification.

policy condition condition_name icmptype type

policy condition condition_name no icmptype

Syntax Definitions

condition_name

The name of the condition.

type

The ICMP type value, in the range 0–255.

Defaults

N/A

Platforms Supported

OmniSwitch 6250

Usage Guidelines

Use the

form of the command to remove an ICMP type value from a condition; however, at least one

classification parameter must be associated with a condition.

Examples

-> policy condition cond12 icmptype 100

Release History

Release 6.6.1; command was introduced.

Related Commands

policy condition

Creates a policy condition.

policy condition icmpcode

Configures an ICMP code value for traffic classification.

qos apply

Applies configured QoS and policy settings to the current configuration.

show policy condition

Shows information about policy conditions configured on the switch.

«
...
1569
1570
1571
1572
1573
...
»

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OmniSwitch 6250

Reviews:

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 1571 / 2018

Search results

Summary of Contents for OmniSwitch 6250

Reviews: