manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 514 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 514

Distributed Spanning Tree Commands

page 16-74

OmniSwitch 6250 CLI Reference Guide

November 2009

Related Commands

MIB Objects

vStpInsPortTable

vStpInsPortNumber

vStpInsPortPathCost

bridge mode

Selects the Spanning Tree operating mode (flat or 1x1) for the switch.

bridge path cost mode

Selects a 32-bit or automatic path cost mode for the switch.

bridge slot/port path cost

Implicit command for configuring the Spanning Tree path cost value for 
a port or an aggregate of ports that applies to the specified CIST or 
VLAN instance.

bridge msti slot/port path cost

Explicit command for configuring the Spanning Tree path cost value for 
a port or an aggregate of ports for an MSTI when the switch is operating 
in either the 1x1 or flat mode.

bridge 1x1 slot/port path cost

Explicit command for configuring the Spanning Tree path cost value for 
a port or an aggregate of ports for a VLAN instance when the switch is 
operating in either the 1x1 or flat mode.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments