Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 841

Page: 841 / 2018

GVRP Commands

OmniSwitch 6250 CLI Reference Guide

November 2009

page 23-15

gvrp restrict-vlan-advertisement

Restricts the advertisement of VLANs on a specific port or an aggregate of ports.

gvrp restrict-vlan-advertisement

{linkagg

agg_num

port

slot/port}

vlan-list

no gvrp restrict-vlan-advertisement {linkagg

agg_num

port

slot/port}

vlan-list

Syntax Definitions

agg_num

The number corresponding to the aggregate group.

slot/port

The slot number for the module and the physical port number on that
module (e.g., 3/1 specifies port 1 on slot 3).

vlan-list

The VLAN ID or the VLAN ID range (e.g., 1-10).

Defaults

By default, VLAN advertisement is not restricted.

Platforms Supported

OmniSwitch 6250

Usage Guidelines

•

Use the

form of this command to allow the propagation of VLANs.

•

GVRP should be enabled on the port before restricting VLAN advertisements on that port.

•

This command affects the GVRP processing only if the applicant mode is set to participant or active.

•

To use the

agg_num

parameter, the link aggregate group should be created and enabled.

Examples

-> gvrp restrict-vlan-advertisement port 3/1 4

-> no gvrp restrict-vlan-advertisement port 3/1 4

-> gvrp restrict-vlan-advertisement port 3/1 6-9

-> no gvrp restrict-vlan-advertisement port 3/1 6-9

-> gvrp restrict-vlan-advertisement linkagg 3 10

-> no gvrp restrict-vlan-advertisement linkagg 3 10

Release History

Release 6.6.1; command was introduced.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OmniSwitch 6250

Reviews:

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 841 / 2018

Search results

Summary of Contents for OmniSwitch 6250

Reviews: