Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 352

Page: 352 / 2018

Link Aggregation Commands

page 12-14

OmniSwitch 6250 CLI Reference Guide

November 2009

lacp linkagg actor admin key

Configures the administrative key associated with a dynamic aggregate group.

lacp linkagg agg_num actor admin key actor_admin_key

lacp linkagg agg_num no actor admin key

Syntax Definitions

agg_num

The number corresponding to the dynamic aggregate group.

actor_admin_key

The administrative key value associated with the dynamic aggregate
group. The valid range is 0–65535.

Defaults

Platforms Supported

OmniSwitch 6250

Usage Guidelines

Use the

form of this command to remove an actor admin key from a dynamic aggregate group.

Examples

-> lacp linkagg 3 actor admin key 2

-> lacp linkagg 3 no actor admin key

Release History

Release 6.6.1; command was introduced.

Related Commands

MIB Objects

alclnkaggAggTable

alclnkaggAggNumber

alclnkaggAggActorAdminKey

parameter

default

actor_admin_key

lacp linkagg size

Creates a dynamic aggregate group.

show linkagg

Displays information about static and dynamic (LACP) aggregate
groups.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OmniSwitch 6250

Reviews:

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 352 / 2018

Search results

Summary of Contents for OmniSwitch 6250

Reviews: