Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 63

Page: 63 / 2018

Chassis Management and Monitoring Commands

OmniSwitch 6250 CLI Reference Guide

November 2009

page 2-11

Examples

-> system timezone mst

-> system timezone -7

-> system ti0

-> system ti12

-> system timezone 12

-> system timezone 05:30

-> system timezone 00:00 hour from UTC

Release History

Release 6.6.1; command was introduced.

Related Commands

MIB Objects

systemServices

systemServicesTimezone

systemServicesTimezoneStartWeek

systemServicesTimezoneStartDay

systemServicesTimezoneStartMonth

systemServicesTimezoneStartTime

systemServicesTimezoneOffset

systemServicesTimezoneEndWeek

systemServicesTimezoneEndDay

systemServicesTimezoneEndMonth

systemServicesTimezoneEndTime

systemServicesEnableDST

system date

Displays or modifies the switch’s current system date.

system time

Displays or modifies the switch’s current system time.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OmniSwitch 6250

Reviews:

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 63 / 2018

Search results

Summary of Contents for OmniSwitch 6250

Reviews: