manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 773 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 773

Port Mobility Commands

OmniSwitch 6250 CLI Reference Guide

November 2009

page 21-5

•

MAC address rules and protocol rules also capture DHCP client traffic.

•

Rules are only assigned to existing VLANs. Use the 

vlan

 command to create a new VLAN.

Examples

-> vlan 10 dhcp mac range 00:00:39:59:0a:0c 00:00:39:59:0a:0f

-> vlan 10 no dhcp mac range 00:00:39:59:0a:0c

Release History

Release 6.6.1; command was introduced.

Related Commands

vlan dhcp mac

Defines a DHCP MAC address rule for an existing VLAN. Mobile ports 
that receive DHCP frames with a source MAC address that matches the 
address specified by this rule are temporarily assigned to the VLAN.

vlan dhcp port

Defines a DHCP port rule for an existing VLAN. The mobile port spec-
ified by this rule is temporarily assigned to the VLAN when it receives 
DHCP frames.

vlan dhcp generic

Defines a generic DHCP rule for an existing VLAN. Mobile ports that 
receive DHCP frames that do not match other DHCP rules are tempo-
rarily assigned to the VLAN.

show vlan

Displays existing VLANs.

show vlan rules

Displays rules defined for VLANs.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments