Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 718

Page: 718 / 2018

Ethernet Port Commands

page 20-46

OmniSwitch 6250 CLI Reference Guide

November 2009

1/21 - 0 DIS MDI -

1/21 - 0 DIS Auto -

1/22 - 0 DIS MDI -

1/22 - 0 DIS Auto -

1/23 - 0 DIS MDI -

1/23 - 0 DIS Auto -

1/24 - 0 Tx MDI -

1/24 Active 65535 Tx-N-Rx Auto C

-> show interfaces 1/24 pause

Slot/Port Active Wait time(usec) Cfg-Pause Cfg-Cross Hybrid Type

-----------+--------+---------------+--------+-----------+-----------

1/24 - 0 Tx MDI -

1/24 Active 65535 Tx-N-Rx Auto C

Release History

Release 6.6.1; command was introduced.

Related Commands

MIB Objects

esmConfTable

esmPortSlot

esmPortIF

esmPortPauseSlotTime

esmPortCfgCrossover

esmPortActiveHybridType

dot3PauseTable

dot3PauseSlotTime

output definitions

Slot/Port

Interface slot and port number

Active

Interface status.

Wait time

The amount of time, in microseconds, the neighbor interface will wait
after receiving a PAUSE frame from the local interface.

Cfg-Pause

The flow control setting (

= transmit,

= receive,

Tx-N-Rx

transmit and receive). Configured through the

interfaces pause

com-

mand.

Cfg-Cross

The user-configured cross-over setting (

Auto

MDI

, or

MDIX

). Con-

figured through the

interfaces crossover

command.

Hybrid Type

The configured active media type for a hybrid port (

= fiber,

= cop-

per,

= not applicable).

show interfaces hybrid pause

Displays flow control pause settings for combo ports.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OmniSwitch 6250

Reviews:

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 718 / 2018

Search results

Summary of Contents for OmniSwitch 6250

Reviews: