manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 1809 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 1809

IP Multicast Switching Commands

OmniSwitch 6250 CLI Reference Guide

November 2009

page 41-91

show ipv6 multicast forward

Display the IPv6 Multicast Switching and Routing forwarding table entries for the specified IPv6 multi-
cast group address or all entries if no IPv6 multicast address is specified.

show ipv6 multicast forward [ipv6_ddress]

Syntax Definitions

ipv6_ddress

IPv6 multicast group address.

Defaults

N/A

Platforms Supported

OmniSwitch 6250 

Usage Guidelines

N/A

Examples

-> show ipv6 multicast forward

Total 1 Forwards

                                                  Ingress    Egress

Group Address   Host Address    Tunnel Address  VLAN  Port  VLAN  Port  

-------------- +---------------+---------------+-----+-----+-----+------

ff05::6         4444::2         ::               1     2/1   1     2/23 

-> show ipv6 multicast forward ff05::6

                                                  Ingress     Egress

Group Address   Host Address    Tunnel Address  VLAN  Port  VLAN  Port  

-------------- +---------------+---------------+-----+-----+-----+------

ff05::6         4444::2         ::               1     2/1   1     2/23 

Release History

Release 6.6.1; command was introduced.

output definitions

Group Address

IPv6 group address of the IPv6 multicast forward.

Host Address

IPv6 host address of the IPv6 multicast forward.

Tunnel Address

IPv6 source tunnel address of the IPv6 multicast forward.

VLAN

VLAN associated with the IPv6 multicast forward.

Port

The slot and port number of the IPv6 multicast forward.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments