manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 1999 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 1999

OmniSwitch 6250 CLI Reference Guide

November 2009

page 5

Loopback Detection Commands

bridge cist hello time 

seconds

bridge 1x1 

vid

 hello time 

seconds

bridge [

instance

] max age 

seconds

bridge cist max age 

seconds

bridge 1x1 

vid

 max age 

seconds

bridge [

instance

] forward delay 

seconds

bridge cist forward delay 

seconds

bridge 1x1 

vid

 forward delay 

seconds

bridge [

instance

]

 bpdu-switching {enable | disable}

bridge path cost mode {auto | 32bit}
bridge [msti 

msti_id

] auto-vlan-containment {enable | disable}

bridge 

instance

 {

slot/port

 | 

logical_port

} {enable | disable}

bridge cist {

slot/port

 | 

logical_port

} {enable | disable}

bridge 1x1 

vid 

{

slot/port

 | 

logical_port

} {enable | disable}

bridge 

instance

 {

slot/port | logical_port

} priority 

priority

bridge 

cist

 {

slot/port | logical_port

} priority 

priority

bridge 

msti

 

msti_id

 {

slot/port | logical_port

} priority 

priority

bridge 

1x1

 

vid

 {

slot/port | logical_port

} priority 

priority

bridge 

instance 

{

slot/port | logical_port

} path cost 

path_cost

bridge 

cist 

{

slot/port | logical_port

} path cost 

path_cost

bridge 

mist 

msti_id 

{

slot/port | logical_port

} path cost 

path_cost

bridge 

1x1 

vid 

{

slot/port | logical_port

} path cost 

path_cost

bridge 

instance

 {

slot/port | logical_port

} mode {forwarding | blocking | dynamic}

bridge cist {

slot/port | logical_port

} mode {dynamic | blocking | forwarding}

bridge 1x1 

vid

 {

slot/port | logical_port

} mode {dynamic | blocking | forwarding}

bridge 

instance

 {

slot/port | logical_port

} connection {noptp | ptp | autoptp | edgeport}

bridge cist {

slot/port 

| 

logical_port

} connection {noptp | ptp | autoptp | edgeport}

bridge 1x1 

vid

 {

slot/port | logical_port

} connection {noptp | ptp | autoptp | edgeport}

bridge cist {

slot/port | logical_port

} admin-edge {on | off | enable | disable}

bridge 1x1 

vid

 {

slot/port 

| 

logical_port

} admin-edge {on | off | enable | disable}

bridge cist {

slot/port | logical_port

} auto-edge {on | off | enable | disable}

bridge 1x1 

vid

 {

slot/port | logical_port

} auto-edge {on | off | enable | disable}

bridge cist {

slot/port

 | 

logical_port

} {restricted-role | root-guard} {on | off | enable | disable}

bridge 1x1 

vid

 {

slot/port | logical_port

} {restricted-role | root-guard} {on | off | enable | 

disable}

bridge cist {

slot/port 

|

 logical_port

} restricted-tcn {on | off | enable | disable}

bridge 1x1 

vid

 {

slot/port | logical_port

} restricted-tcn {on | off | enable | disable}

bridge cist txholdcount 

value

bridge 1x1 

vid

 txholdcount {

value

}

bridge rrstp
no bridge rrstp

bridge rrstp ring

 

ring_id 

 

port1 {

slot/port

 | linkagg

 

agg_num

}

 

port2

 

{

slot/port

 | linkagg

 

agg_num

} vlan-tag 

vlan_id

 

[status

 

{enable | disable}]

no bridge rrstp ring

 [

ring_id

]

bridge rrstp ring

 

ring_id 

vlan-tag

 

vid

bridge rrstp ring

 

ring_id 

status

 

{enable | disable}

show spantree [

instance

]

show spantree cist
show spantree msti [

msti_id

]

show spantree 1x1 [

vid

]

show spantree [

instance

] ports [forwarding | blocking | active | configured]

show spantree cist ports [forwarding | blocking | active | configured]
show spantree msti [

msti_id

] ports [forwarding | blocking | active | configured]

show spantree 1x1 [

vid

] ports [forwarding | blocking | active | configured]

show spantree mst region
show spantree mst [

msti_id

] vlan-map

show spantree cist vlan-map
show spantree mst 

vid

 vlan-map

show spantree mst port {

slot/port

 | 

logical_port

}

show bridge rrstp configuration
show bridge rrstp ring [

ring_id

]

bridge mode 1x1 pvst+ {enable | disable}
bridge port {

slot/port

 | 

agg_num

} pvst+ {auto | enable | disable}

Loopback Detection Commands

loopback-detection {enable | disable}
loopback-detection port slot/port [-port2] {enable | disable}
loopback-detection transmission-timer seconds
loopback-detection autorecovery-timer seconds
show loopback-detection
show loopback-detection port [slot/port]
show loopback-detection statistics port [slot/port]

Source Learning Commands

mac-address-table [permanent] 

mac_address

 {

slot/port | 

linkagg

 

link_agg

} 

vid 

[bridging | 

filtering]

no mac-address-table [permanent | learned] [

mac_address

 {

slot/port | 

linkagg 

link_agg

} 

vid

]

mac-address-table static-multicast 

multicast_address 

{

slot1

/

port1

[-

port1a

] [

slot2/port2

[-

port2a

]

...

]

 | 

linkagg 

link_agg

} 

vid

no mac-address-table static-multicast [

multicast_address

 {

slot1

/

port1

[-

port1a

] [

slot2/port2

[-

port2a

]

...

]

 | 

linkagg 

link_agg

} 

vid

]

mac-address-table aging-time 

seconds

no mac-address-table aging-time
source-learning {port 

slot/port1

[

-port2

]

 | 

linkagg

 

linkagg_num

}

 

{enable | disable}

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments