manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 618 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 618

Loopback Detection Commands

page 17-2

OmniSwitch 6250 CLI Reference Guide

November 2009

loopback-detection

Enables or disables Loopback Detection (LBD) globally on the switch. 

loopback-detection {enable | disable}

Syntax Definitions

enable

Enables LBD on the switch. 

disable

Disables LBD on the switch.

Defaults

Platforms Supported

OmniSwitch 6250-Metro Models

Usage Guidelines

•

LBD can be enabled globally and per port without any dependency but loopback-detection will be 
operational only if LBD is enabled globally and also on the specific port.

•

LBD can be configured for a port and the configuration can be applied and retained, whether or not 
LBD is enabled globally. However, LBD functionality on a port is available only when LBD is enabled 
globally on the switch. 

Examples

-> loopback-detection enable

Release History

Release 6.6.1; command was introduced.

Related Commands

MIB Objects

alaLdbConfigTable

alaLdbGLobalConfigStatus

parameter

default

enable | disable

disable

loopback-detection port

Enables or disables LBD on a specific port. 

show loopback-detection

Displays LBD configuration information.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments