manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 1204 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 1204

IPv6 Commands

page 30-38

OmniSwitch 6250 CLI Reference Guide

November 2009

clear ipv6 neighbors

Removes all entries, except static entries, from IPv6 Neighbor Table. 

clear ipv6 neighbors

Syntax Definitions

N/A

Defaults

N/A

Platforms Supported

OmniSwitch 6250 

Usage Guidelines

This commands only clears dynamic entries. If static entries have been added to the table, they must be 
removed using the 

no 

form of the 

ipv6 neighbor

 

command.

Examples

-> clear ipv6 neighbors

Release History

Release 6.6.1; command was introduced.

Related Commands

MIB Objects

alaIPv6NeighborTable

alaIPv6ClearNeighbors

ipv6 neighbor

Configures a static entry in IPv6 Neighbor Table.

show ipv6 neighbors

Displays IPv6 Neighbor Table.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments