Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 1369

Page: 1369 / 2018

RIP Commands

OmniSwitch 6250 CLI Reference Guide

November 2009

page 33-29

Release History

Release 6.6.1; command was introduced.

Related Commands

MIB Objects

alaProtocolRip

alaRipProtoStatus

alaRip2IfConfAugTable

alaRip2IfConfName

alaRip2IfRecvPkts

alaRip2IfIpConfStatus

rip2IfConfTable

rip2IfConfAddress

rip2IfConfAuthType

rip2IfConfAuthKey

rip2IfConfSend

rip2IfConfReceive

rip2IfConfDefaultMetric

rip2IfStatTable

rip2IfStatRcvBadPackets

rip2IfStatRcvBadRoutes

rip2IfStatSentUpdates

Interface Config AuthKey
Length

The authentication key length used for the RIP interface.

Interface Config Send-Version

Interface send option (none, v1, v2, and v1 compatible). Default is v2.

Interface Config Receive-Ver-
sion

Interface receive option (none, v1, v2, and both). Default is both.

Interface Config Default Met-
ric

Default redistribution metric. Default is 1.

Received Packets

Number of packets received on the interface.

Received Bad Packets

Number of bad packets received and discarded. Normally this value is
zero (0).

Received Bad Routes

Number of bad routes received and discarded. Normally this value is
zero (0).

Sent Updates

Number of RIP routing table updates sent.

ip rip interface

Enables/disables RIP for a specific interface.

output definitions (continued)

«
...
1367
1368
1369
1370
1371
...
»

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OmniSwitch 6250

Reviews:

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 1369 / 2018

Search results

Summary of Contents for OmniSwitch 6250

Reviews: