Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 627

Page: 627 / 2018

Loopback Detection Commands

OmniSwitch 6250 CLI Reference Guide

November 2009

page 17-11

show loopback-detection statistics port

Displays LBD statistics information for a specific port on the switch.

show loopback-detection statistics port

[

slot/port

]

Syntax Definitions

N/A

Defaults

N/A

Platforms Supported

OmniSwitch 6250-Metro Models

Usage Guidelines

•

Use this command to view LDB statistics of a specific port on a switch.

Examples

-> show loopback-detection statistics port 1/1

LBD Port Statistics

LBD Packet Send

: 1

Invalid LBD Packet Received

: 0

Release History

Release 6.6.1; command was introduced.

Related Commands

MIB Objects

alaLdbConfigTable

alaLdbGLobalConfigStatus

output definitions

Slot/Port

The slot/port number LBD port.

LBD Packet Send

The number of LBD packet sent from the port.

Invalid LBD Packet Received

The number of invalid LBD packets received on the port.

loopback-detection

Enables or disables LBD globally on the switch.

show loopback-detection

Displays LBD configuration information for the switch or for a specific
port.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OmniSwitch 6250

Reviews:

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 627 / 2018

Search results

Summary of Contents for OmniSwitch 6250

Reviews: