manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 1332 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 1332

DHCP Relay Commands

page 32-56

OmniSwitch 6250 CLI Reference Guide

November 2009

Release History

Release 6.6.1; command was introduced.

Related Commands

MIB Objects

iphelperDhcpSnoopingPortTable

iphelperDhcpSnoopingPortIfIndex

iphelperDhcpSnoopingPortTrustMode

iphelperDhcpSnoopingPortIpSourceFiltering

iphelperDhcpSnoopingPortOption82Violation

iphelperDhcpSnoopingPortMacAddrViolation

iphelperDhcpSnoopingPortDhcpServerViolation

iphelperDhcpSnoopingPortRelayAgentViolation

iphelperDhcpSnoopingPortBindingViolation

output definitions

Slot/Port

The slot number for the module and the physical port number on that 
module (e.g., 3/1 specifies port 1 on slot 3). 

Trust Mode

The DHCP Snooping trust mode for the port (

Blocked

, 

Client-Only

, or 

Trusted

). Configured through the 

ip helper dhcp-snooping port

 com-

mand.

IP Src Filtering

Indicates whether or not IP source filtering is enabled for the port 
(

Enabled

 or 

Disabled

). Configured through the 

ip helper dhcp-snoop-

ing port ip-source-filtering

 command.

Opt82 Violation

The number of DHCP packets dropped due to a DHCP Snooping 
Option-82 violation.

MAC Violation

The number of DHCP packets dropped due to a mismatch between the 
packet source MAC address and the client hardware address contained 
within the packet.

Server Violation

The number of DHCP server packets dropped because they originated 
from outside the network or firewall. 

Relay Violation

The number of DHCP packets dropped because the packet included a 
relay agent IP address that was not 0.0.0.0.

Binding Violation

The number of DHCP packets dropped due to a mismatch between 
packets received and binding table information.

show ip helper

Displays current DHCP Relay configuration information. 

show ip helper dhcp-snooping 
vlan

Displays a list of DHCP Snooping VLANs.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments