manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 146 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 146

Network Time Protocol Commands

page 5-6

OmniSwitch 6250 CLI Reference Guide

November 2009

ntp client

Enables or disables NTP operation on the switch.

ntp client {enable | disable}

Syntax Definitions

enable

Enables NTP.

disable

Disables NTP.

Defaults

NTP protocol is disabled by default.

Platforms Supported

OmniSwitch 6250 

Usage Guidelines

Use this command to enable or disable NTP. Before NTP can be enabled, an NTP server must be speci-
fied using the 

ntp server

 command.

Examples

-> ntp client enable

-> ntp client disable

Release History

Release 6.6.1; command was introduced. 

Related Commands

MIB Objects

alaNtpEnable 

ntp server

Specifies an NTP server from which the switch will receive updates.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments