manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 1140 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 1140

IP Commands

page 29-92

OmniSwitch 6250 CLI Reference Guide

November 2009

Related Commands

MIB Objects

alaRouteMapRedistProtoTable

alaRouteMapRedistRouteMapIndex

alaRouteMapTable

alaRouteMapIndex

alaRouteMapSequence

alaRouteMapType

alaRouteMapValue

alaRouteMapRowStatus

ip route-map action

Creates a route map for redistribution and sets the status of route 
map to permit or deny.

ip route-map match ip address

Matches the route with the specified IPv4 address or with addresses 
contained in an IPv4 access list specified by the access list name.

ip route-map match ipv6 
address

Matches the route with the specified IPv6 address or with addresses 
contained in an IPv6 access list specified by the access list name

ip route-map match ip-
nexthop

Matches the routes that have a next-hop router address permitted 
by the specified access list.

ip route-map match ipv6-
nexthop

Matches the routes that have an IPv6 next-hop router address per-
mitted by the specified access list

ip route-map match tag

Permits or denies a route based on the specified next-hop IP 
address.

ip route-map match tag

Matches the tag value specified in the route map with the one that 
the routing protocol learned the route on.

ip route-map match metric

Matches the metric value specified in the route map with the one 
that the routing protocol learned the route on.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments