Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 720

Page: 720 / 2018

Ethernet Port Commands

page 20-48

OmniSwitch 6250 CLI Reference Guide

November 2009

Examples

-> show interfaces 1/2 accounting

1/2 ,

Rx undersize packets = 0,

Tx undersize packets = 0,

Rx oversize packets = 0,

Tx oversize packets = 0,

Rx packets 64 Octets = 3073753,

Rx packets 65To127 Octets = 678698,

Rx packets 128To255 Octets = 21616,

Rx packets 256To511 Octets = 21062,

Rx packets 512To1023 Octets = 2,

Rx packets 1024To1518 Octets = 84,

Rx packets 1519to4095 Octets = 0,

Rx packets 4096ToMax Octets = 0,

Rx Jabber frames = 0

Release History

Release 6.6.1; command was introduced.

Related Commands

output definitions

Rx undersize packets

Number of undersized packets received.

Tx undersize packets

Number of undersized packets transmitted.

Rx oversize packets

Number of oversized packets received.

Tx oversize packets

Number of oversized packets transmitted.

Rx packets Octets

Number of packets received in each listed octet range.

Rx Jabber frames

Number of jabber packets received (longer than 1518 octets).

Tx deferred frames

Number of packets for which transmission was delayed (Ethernet
only).

show interfaces

Displays general interface information (e.g., hardware, MAC
address, and input/output errors).

show interfaces counters

Displays interface counter information (e.g., unicast packets
received/transmitted).

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for OmniSwitch 6250

Reviews:

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 720 / 2018

Search results

Summary of Contents for OmniSwitch 6250

Reviews: