manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 1620 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 1620

QoS Policy Commands

page 39-124

OmniSwitch CLI Reference Guide

November 2009

policy action 802.1p

Configures a value to be set in the 802.1p bits of the 802.1Q byte of an outgoing frame for traffic that 
matches a policy with this action.

policy action action_name 802.1p 802.1p_value 

policy action action_name no 802.1p

Syntax Definitions

action_name

The name of the action.

802.1p_value

The priority value to be set in 802.1Q frames. Values range from 0 
(lowest priority) to 7 (highest priority). 

Defaults

N/A 

Platforms Supported

OmniSwitch 6250 

Usage Guidelines

•

Use the 

no

 form of the command to remove an 802.1p value from a policy action.

•

Note that specifying both ToS and DSCP in the same action is not allowed.

•

An 802.1p or ToS/DSCP action always sets the packet priority. For 802.1p marking, the priority is set 
according to the marked 802.1p. For ToS marking, the priority is set according to the marked ToS. For 
DSCP marking, the priority is set according to the marked DSCP. 

Examples

-> policy action action4 802.1p 7

-> policy action action4 no 802.1p

Release History

Release 6.6.1; command was introduced.

Related Commands

qos apply

Applies configured QoS and policy settings to the current configuration. 

policy action

Creates a policy action.

show policy action

Displays information about actions configured on the switch.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments