manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 1622 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 1622

QoS Policy Commands

page 39-126

OmniSwitch CLI Reference Guide

November 2009

policy action dscp

Configures a Differentiated Services Code Point (DSCP) value to be set in an outgoing flow for traffic that 
matches rules with this action.

policy action action_name dscp dscp_value 

policy action action_name no dscp

Syntax Definitions

action_name

The name of the action.

dscp_value

The DSCP value to be set, in the range 0–63.

Defaults

N/A

Platforms Supported

OmniSwitch 6250

Usage Guidelines

•

Use the 

no

 form of this command to remove a DSCP value from a policy action.

•

Note that specifying both ToS and DSCP in the same action is 

not

 allowed.

•

An 802.1p or ToS/DSCP action always sets the packet priority. For 802.1p marking, the priority is set 
according to the marked 802.1p. For ToS marking, the priority is set according to the marked ToS. For 
DSCP marking, the priority is set according to the marked DSCP. 

Examples

-> policy action action2 dscp 61

-> policy action action2 no dscp

Release History

Release 6.6.1; command was introduced.

Related Commands

qos apply

Applies configured QoS and policy settings to the current configuration. 

policy action

Creates a policy action.

show policy action

Displays information about actions configured on the switch.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments