manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 1635 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 1635

QoS Policy Commands

OmniSwitch CLI Reference Guide

November 2009

page 39-139

policy action mirror

Mirrors ingress packets that match a mirroring policy to the specified port.

policy action action_name ingress mirror slot/port

policy action action_name no mirror slot/port

Syntax Definitions

action_name

The name of the action.

ingress

Mirrors ingress packets.

slot/port

The slot and port number that will receive the mirrored traffic. 

Defaults

N/A

Platforms Supported

OmniSwitch 6250 

Usage Guidelines

•

Use the 

no

 form of the command to remove 

mirror

 from the policy action. 

•

Use this command to configure a mirror-to-port (MTP) action that is used for policy based mirroring.

•

Only one MTP session is supported at any given time. As a result, all mirroring policies should specify 
the same MTP port. 

•

Policy based mirroring and the port based mirroring feature can run simultaneously on the same 
switch. If a packet qualifies for both types of sessions, the packet is copied to the destination for both 
sessions.

Examples

-> policy action a1 mirror 1/7 (default ingress)

-> policy action a1 ingress mirror 1/7 

-> policy action a1 no mirror

Release History

Release 6.6.1; command was introduced.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments