manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 1626 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 1626

QoS Policy Commands

page 39-130

OmniSwitch CLI Reference Guide

November 2009

policy action permanent gateway ip

Used for Policy Based Routing (PBR). Routed flows to which this action is applied will be directed to the 
IP address specified in the action regardless of whether or not a route already exists in the switch routing 
table.

policy action action_name permanent gateway ip ip_address 

policy action action_name no permanent gateway ip

Syntax Definitions

action_name

The name of the action.

ip_address

The destination IP address to which packets will be routed.

Defaults

N/A

Platforms Supported

OmniSwitch 6250-Metro Models

Usage Guidelines

•

Use the 

no

 form of the command to remove a gateway IP address from a policy action.

•

If the gateway goes down, the traffic to be routed over the gateway will be dropped.

Examples

-> policy action pbr2 permanent gateway ip 10.10.2.1

-> policy action pbr2 no permanent gateway ip

Release History

Release 6.6.1; command was introduced.

Related Commands

qos apply

Applies configured QoS and policy settings to the current configuration. 

show policy action

Displays information about actions configured on the switch.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments