manualshive.com logo in svg

Alcatel-Lucent OmniSwitch 6250, Cli Reference Manual, Page: 1603 / 2018

Share
Download
Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual Download Page 1603

QoS Policy Commands

OmniSwitch CLI Reference Guide

November 2009

page 39-107

policy condition destination port group

Associates a destination port group with a policy condition. Note that this condition is supported only in 
combination with a multicast condition (

multicast ip

, 

multicast ipv6

, or 

multicast network group

).

policy condition condition_name destination port group group_name

policy condition condition_name no destination port

Syntax Definitions

condition_name

The name of the condition. May be an existing condition name or a new 
condition.

group_name

The name of the destination port group. Port groups are configured 
through the 

policy port group

 command. 

Defaults

N/A

Platforms Supported

OmniSwitch 6250 

Usage Guidelines

Use the 

no

 form of the command to remove a destination port group from a condition; however, at least 

one classification parameter must be associated with a condition.

Examples

-> policy condition cond6 destination port group portgr4 multicast ip any

Release History

Release 6.6.1; command was introduced.

Related Commands

qos apply

Applies configured QoS and policy settings to the current configuration. 

policy port group

Configures a port group and its associated slot and port numbers.

policy condition

Creates a policy condition.

show policy condition

Shows information about policy conditions configured on the switch.

Summary of Contents for OmniSwitch 6250



































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments