![background image](http://html1.mh-extra.com/html/omron/cj1w-c113-rev-02-2008/cj1w-c113-rev-02-2008_operation-manual_742339364.webp)
337
Error Code Lists
Section 11-5
Data transfer
Write transfer:
number of words
error
8310
The number of write words was set
to 0 or exceeded the number of
write data words.
The parameters for the origin
search high speed and the origin
search proximity speed were not
sent together.
Execute the com-
mand again after
changing the incor-
rect setting.
The current START
command will not
be executed, but
other operating
axes will not be
affected.
Write transfer:
source word
error
8311
The write source word or the write
source area was outside the setta-
ble range.
Write transfer:
destination
address error
8312
The write destination address was
outside the settable range.
Read transfer:
number of words
error
8320
The number of read words was set
to 0 or exceeded the number of
read data words.
Read transfer:
source address
error
8321
The read source address was out-
side the settable range.
Read transfer:
destination word
error
8322
The read destination word or the
read destination area was outside
the settable range.
Error counter
reset/
Origin adjust-
ment output
Error counter
reset/
Origin adjust-
ment output error
8400
There was an attempt to output a
error counter reset/origin adjust-
ment output when the output
couldn’t be used.
Execute the com-
mand again after
checking that the
output can be used
and changing the
ladder program if
necessary.
The axis will be
decelerated to a
stop. Other operat-
ing axes will not be
affected.
Override
Override error
8500
The override setting was outside
the settable range (1 to 999%).
Execute the com-
mand again after
correcting the data.
Positioning
Positioning timer
timeout
8600
The Servo Drive’s positioning com-
pleted signal did not go ON within
the axis parameters’ specified
time.
Execute the com-
mand again after
making adjust-
ments such as
adjusting the posi-
tioning monitor time
or the servo sys-
tem’s gain, or
checking the wiring
for the positioning
completed signal
and correcting if
necessary.
The designated
axis will be deceler-
ated to a stop.
Other operating
axes will not be
affected.
Overflow
8601
The movement distance is too
long (greater than 2,147,483,646
pulses, or greater than
2,147,483,520 pulses for linear
interpolation) and so operation is
not possible.
Execute the com-
mand again after
reducing the dis-
tance to move in
one operation (by
changing the posi-
tion data).
The designated
axis will be deceler-
ated to a stop.
Other operating
axes will not be
affected.
Group
Name
Code
Cause
Clearing method
Operation after
error
Содержание CJ1W-C113 - REV 02-2008
