Timewave PK-900 Operating Manual Download Page 262

Page: 262 / 392

________________________________________________________________________________

QHpacket "n/n" Default: 10/2 (Modems 10/2)

Mode: Packet Host: QH

_________________________________ Parameters: __________________________________

"n/n" - Modem numbers to be selected when the HF Packet mode is entered.

________________________________________________________________________________

QHPACKET sets the PK-900 modem that will automatically selected when the HF

Packet mode is entered. To enter the HF packet mode, the VHF command must be

OFF for the selected Radio Port.

See the PACKET and MODEM commands for more information.

________________________________________________________________________________

QMORse "n" Default: 12 (Modem 12)

Mode: Morse Host: QO

_________________________________ Parameters: __________________________________

"n" - Modem number to be selected when the MORSE mode is entered.

________________________________________________________________________________

QMORSE sets the PK-900 modem that will automatically selected when the Morse

mode is entered.

See the MORSE and MODEM commands for more information.

________________________________________________________________________________

QRtty "n" Default: 1 (Modem 1)

Mode: Baudot and ASCII RTTY Host: QR

_________________________________ Parameters: __________________________________

"n" - Modem number to be selected when the ASCII or Baudot RTTY modes are

entered.

________________________________________________________________________________

QRTTY sets the PK-900 modem that will automatically selected when the Baudot

or ASCII RTTY modes are entered.

See the BAUDOT, ASCII and MODEM commands for more information.

1/93 A-84

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands