Timewave PK-900 Operating Manual Download Page 266

Page: 266 / 392

________________________________________________________________________________

REDispla "n" Default: $12 <CTRL-R>

Mode: All Host: RD

_________________________________ Parameters: __________________________________

"n" - 0 to $7F (0 to 127 decimal) specifies an ASCII character code.

________________________________________________________________________________

REDISPLA changes the redisplay-line input editing character.

Parameter "n" is the numeric ASCII code for the character you'll use when you

want to re-display the current input line.

Type the REDISPLA character (default <CTRL-R>) to re-display a command or text

line you've just typed. This can be helpful when editing a line especially if

your terminal does not support <BACKSPACE>. It can also be used in Packet to

display a packet that might have been received while you were typing. A

<BACKSLASH> is appended to old line, and the corrected line is shown below it.

________________________________________________________________________________

RELink ON|OFF/ON|OFF Default: OFF/OFF

Mode: Packet Host: RL

_________________________________ Parameters: __________________________________

ON - The PK-900 will try to automatically reconnect the distant station

after the link has timed out on retries.

OFF - The PK-900 will not attempt to re-establish the failed link.

________________________________________________________________________________

Set RELINK ON if you want the PK-900 to automatically try to reconnect to a

distant packet station if the link fails. This is settable for each radio port.

________________________________________________________________________________

RESET Immediate Command

Mode: Command Host: RS

________________________________________________________________________________

RESET is an immediate command that resets all parameters to PK-900's PROM

default settings and reinitializes the PK-900. All personalized parameters,

monitor lists and MailDrop messages will be lost.

________________________________________________________________________________

RESptime "n/n" Default: 0/0 (000 msec.)

Mode: Packet Host: RP

_________________________________ Parameters: __________________________________

"n" - 0 to 250 specifies 100-millisecond intervals.

________________________________________________________________________________

RESPTIME adds a minimum delay before your PK-900 sends acknowledgment packets.

This delay may run concurrently with the default wait time set by DWAIT and any

random wait in effect. RESPTIME may be set for each Radio Port.

During a file transfer, RESPTIME can help avoid data/ack collisions caused by

the sending stations TNC pausing briefly between transmitted data frames.

3/93 A-88

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands