Timewave PK-900 Operating Manual Download Page 151

Page: 151 / 392

CHAPTER 10

SIGNAL IDENTIFICATION AND TDM OPERATION

10.1 Overview

As you tune across the High-Frequency bands these days you find an

ever increasing number of digital signals. These signals range from

the simple Murray Baudot code to ASCII and even packetized data. With

the large number of speeds, formats and shifts now in use, it is

difficult to determine what kind of signal you are listening to. Even

with a knowledge of digital communications, it is still time-consuming

to set the communication parameters correctly.

SIAM stands for Signal Identification and Acquisition Mode, and allows

a wide variety of digital signals to be automatically analyzed so they

can be easily copied with the PK-900. SIAM will "listen" to a

signal for a few seconds and then display the type of signal and its

speed to the user. The user can then decide whether or not to copy

the signal, or simply go on to the next signal.

SIAM makes the PK-900 more useful to the radio amateur and the

Short-Wave Listener. Whether tuning across 20 meters, or searching

the Short-Wave bands, when you find a signal SIAM will help you decide

what it is, and tune it in without time-consuming trial and error.

NOTE: Outside the Amateur bands, many of the RTTY signals employ

sophisticated encryption schemes and are not copyable by the PK-900.

10.2 SIAM Operation

Before entering the Signal Identification mode, set the default modem

(QSIGNAL) to the number you wish to use from the list below.

1: RTTY/TOR 170: 2125/2295, 45 bps 2: RTTY/TOR 170: 2125/2295, 100 bps

3: RTTY/TOR 200: 2110/2310, 45 bps 4: RTTY/TOR 200: 2110/2310, 100 bps

5: RTTY/TOR 425: 2125/2550, 100 bps 6: RTTY/TOR 850: 2125/2975, 100 bps

7: RTTY/TOR 850: 2125/1275, 100 bps

If you are using an AEA PAKRATT program, follow the instructions in

the program manual to enter the Signal mode.

If you are using a terminal, simply type "SIGNAL" or "SI" from the

Command Mode followed by the <Enter> key to enter the SIAM mode on

Radio Port 1. The PK-900 responds by displaying the previous mode:

Opmode was XXXXX

Opmode now SIgnal

Now you are ready to tune in an unknown FSK signal.

1/93 10-1

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands