Timewave PK-900 Operating Manual Download Page 275

Page: 275 / 392

________________________________________________________________________________

TEST Immediate Command

Mode: Command Host: TE

________________________________________________________________________________

TEST initiates the PK-900 self test function. For the modem self test to

operate, both radio ports must have the loopback jumpers installed.

The self test feature tests operating voltages, both radio channel modems and

all keying lines. A probe connected to either an internal test point or pin

16 of the serial connector is necessary to test the keying lines.

________________________________________________________________________________

TIme "n" Default: $14 <CTRL-T>

Mode: All Host: TM

_________________________________ Parameters: __________________________________

"n" - 0 to $7F (0 to 127 decimal) specifies an ASCII character code.

________________________________________________________________________________

The TIME command specifies which control character sends the time-of-day in the

text you type into the transmit buffer or into a text file stored on disk.

At transmit time, the PK-900 reads the embedded control code (default

<CTRL-T>), reads the time-of-day from the PK-900's internal clock and then

sends the time to the radio in the data transmission code in use at that time.

If the DAYTIME has not been set, and a control-T will cause the PK-900 to send

an asterisk (*).

When DAYSTAMP is set ON, the date is transmitted with the time.

NOTE: The TIME command cannot be embedded in CTEXT, BTEXT, MTEXT or AAB.

________________________________________________________________________________

TMail ON|OFF Default: OFF

Mode: AMTOR, PACTOR Host: TL

_________________________________ Parameters: __________________________________

ON - The PK-900 operates as a personal AMTOR or PACTOR BBS or MailDrop.

OFF - The PK-900 only operates as a normal CCIR 476 or 625 controller.

________________________________________________________________________________

The PK-900's MailDrop is a personal mailbox that uses a subset of the

W0RLI/WA7MBL PBBS commands and is similar to operation of APLINK stations. When

TMAIL is ON and another station establishes an ARQ link with your MYSELCAL or

MYIDENT, the remote AMTOR station may leave messages for you or read messages

from you. Third-party messages are not accepted by your AMTOR MailDrop unless

3RDPARTY is ON.

See the MDCHECK, TMPROMPT, MDMON, MTEXT, MMSG MYSELCAL and MYIDENT commands.

3/93 A-97

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands