Timewave PK-900 Operating Manual Download Page 337 | Manualshive

Page: 337 / 392

background image

13

PK-900 Gateway Option Supplement

L

+++ Listening OFF

K

B7B de N7ML (B,C,D,J,L,N,S,?) >

S(end)

The Gateway sends UI frames with a destination of “CQ.” The source
field is the user’s callsign with the SSID decremented by one. The
Gateway holds the data characters until the user sends a (RETURN),
whereupon the held data is broadcast.

Error messages to the connected station (user)

Bad

An invalid callsign in response to the AMTOR prompt

Enter your

callsign

. An invalid callsign as one of the arguments in the Connect

command. An invalid argument to the

PORT

command.

Too many

Too many callsigns in the Connect command. Arguments in the Bye,
Disconnect, Jheard, Listen, Nodes or Send commands.

Too long

Command longer than 85 characters. PACTOR callsign in Connect
command was longer than 8 characters.

Range

PORT

command argument not

1

or

2

.

Callsign

No argument in the Connect command.

What?

Unrecognized command.

?VIA

Connect command: second argument wasn’t

STAY

or

VIA

.

Not during connect

While a connect attempt was in progress, the user issued a Listen, a
Send, or another Connect command or tried to change Ports; the user
must first disconnect.

Already disconnected

The user tried to disconnect when no connect was in progress.

Need MYSelcal

The packet user tried to make an AMTOR connect, but your TNC’s

MYSELCAL

wasn’t set.

None heard

The

JHEARD

or Nodes list is empty.

Channel busy

Connect or Send command while there is AMTOR or PACTOR
activity on the channel. Gateway uses synced radio DCD to determine
activity.

Port busy

Connect, Listen or Send command on a packet port where all multi-
connect channels are being used. Attempt to use the

PORT

command

to access a port whose operating mode isn’t packet, AMTOR Standby
or PACTOR Standby. Port 2 user attempt to access AMTOR or

«
...
335
336
337
338
339
...
»

Summary of Contents for PK-900









































































































































































































































































































































































































Reviews:

No comments

Related manuals for PK-900

Brand: K&K Pages: 6

Brand: Saitek Pages: 44

Brand: Baader Planetarium Pages: 7

Brand: Beaphar Pages: 2

Brand: YOKOGAWA Pages: 2

ALICAT SCIENTIFIC PC

Brand: Halma Pages: 2

ALICAT SCIENTIFIC PCD

Brand: Halma Pages: 46

REVOLUTION Pro Controller 2

Brand: Nacon Pages: 11

Brand: Nacon Pages: 18

Brand: Nacon Pages: 24

Brand: Nabco Pages: 35

Brand: Saab Pages: 4

Brand: Madison AV Pages: 2

Brand: Daikin Pages: 64

Q.PEAK DUO BLK ML-G10/t Series

Brand: Qcells Pages: 13

Brand: Fantini Cosmi Pages: 25

Brand: Woodward Pages: 32

Brand: SAGEMCOM Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands