Timewave PK-900 Operating Manual Download Page 172

Page: 172 / 392

Always make sure that the port 2 packet baud rate HBAUD is appropriate

for the modem you have chosen. For instance to operate 1200 baud VHF

packet on radio port 2, the packet baud rate (HBAUD) must be 1200

bauds. Type HBAUD /1200 to select 1200 baud on radio port 2.

11.10.1 Selecting Modems

The various modems available in the PK-900 can be seen with the

DIRECT(ory) command. To display all the available modems simply

enter the Command Mode of the PK-900 and then type DIR as shown.

DIR <Enter>

The PK-900 will respond with the following:

- Port 1 - - Port 2 -

1: FSK 45 bps 170: 2125/2295 1: Internal 200: 1070/1270

2: FSK 100 bps 170: 2125/2295 2: Internal 200: 2025/2225

3: FSK 45 bps 200: 2110/2310 3: Internal 1000: 1200/2200

4: FSK 100 bps 200: 2110/2310 4: Internal 1000: 1200/2200

eq.

5: FSK 100 bps 425: 2125/2550 5: Internal 200: 1180/980

6: FSK 100 bps 850: 2125/2975 6: Internal 200: 1850/1650

7: FSK 100 bps 850: 1275/2125 7: Internal 800: 2100/1300

8: Analog 900/2500 8: Internal 800: 2100/1300 eq.

9: FSK 2400 bps 800: 1300/2100 9: Internal option

10: FSK 300 bps 200: 2110/2310 10: Modem disconnect header

11: FSK 1200 bps 1000: 1200/2200

12: Morse 750

cmd:

Any modem from the list may be loaded with the MODEM command, but

only the 100 (or higher) baud modems listed will operate in PACTOR.

For example, to operate PACTOR on radio port 1 and 1200 bps VHF packet

on radio port 2 you must select modems for radio ports 1 and 2.

First, enter the Command Mode of the PK-900 and then type MODEM 4/4 as

shown below:

MODEM 4/4 <Enter>

The PK-900 will respond with the following:

MODem was x/x (The previous modems)

MODem now 4/4

11.10.2 Displaying Received Data

The Radio command may be used to disable port 2. This may be

desirable when operating PACTOR and you do not want to be disturbed

with any packet signals that may be received on radio port 2. To

disable port 2, enter:

RADIO ON/OFF <Enter> or RADIO 1/0 <Enter>

For dual port operation, type

RADIO ON/ON <Enter> or RADIO 1/2 <Enter>

3/93 11-16

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Timewave PK-900, Operating Manual, Page: 172 / 392

Search results

Summary of Contents for PK-900

Reviews: