Timewave PK-900 Operating Manual Download Page 258

Page: 258 / 392

________________________________________________________________________________

PARity "n" Default: 3 (even)

Mode: All Host: PR

_________________________________ Parameters: __________________________________

"n" - 0 to 3 selects a parity option from the table below.

________________________________________________________________________________

PARITY sets the PK-900's RS-232 terminal parity according to the following:

0 = no parity, 1 = odd parity, 2 = no parity, 3 = even parity

The parity bit, if present, is stripped on input and is not checked in Command

and Converse modes. In Transparent mode all eight bits (including parity) are

transmitted. The change will not take effect until a RESTART is performed.

Be sure to change the computer or terminal to the same parity setting.

________________________________________________________________________________

PASs "n" Default: $16 <CTRL-V>

Mode: Packet/ASCII Host: PS

_________________________________ Parameters: __________________________________

"n" - 0 to $7F (0 to 127 decimal) specifies an ASCII character code.

________________________________________________________________________________

PASS selects the ASCII code for the character used for the "pass" input editing

commands (default <CTRL-V>). The PASS character signals that the following

character is to be included in a packet or ASCII text string.

________________________________________________________________________________

PASSAll ON|OFF/ON|OFF Default: OFF/OFF

Mode: Packet Host: PX

_________________________________ Parameters: __________________________________

ON - Your PK-900 will accept packets with valid or invalid CRCs.

OFF - Your PK-900 will accept packets with valid CRCs only.

________________________________________________________________________________

PASSALL turns off the PK-900's packet error-detecting mechanism and displays

received packets with invalid CRCs. The is settable for each Radio Port.

PASSALL is normally turned OFF (default); which ensures that packet data is

error-free by rejecting packets with invalid CRC fields. When PASSALL is ON,

packets are displayed, despite CRC errors. The MHEARD logging is disabled

since the call signs detected may be incorrect.

________________________________________________________________________________

PErsist "n/n" Default: 63/63

Mode: Packet Host: PE

_________________________________ Parameters: __________________________________

"n" - 0 to 255 specifies the threshold for a random attempt to transmit.

________________________________________________________________________________

The PERSIST parameter works with the PPERSIST and SLOTTIME parameters to achieve

true p-persistent CSMA (Carrier-Sense Multiple Access) in Packet operation.

PERSIST is settable on each radio port to allow for different types of operation.

3/93 A-80

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands