Timewave PK-900 Operating Manual Download Page 260

Page: 260 / 392

________________________________________________________________________________

PT200 ON|OFF Default: ON

Mode: PACTOR Host: PB

________________________________________________________________________________

PACTOR uses an adaptive data rate selection scheme. The normal data rate is 100

baud. If PT200 is ON (default) and conditions permit, the data rate will be

automatically shifted to 200 baud. If the error rate becomes too high at 200

baud the data rate will automatically be reduced to 100 baud. There can be

conditions where the data rate is frequently shifting, causing a loss in the

actual information data rate. When PT200 is OFF, the PACTOR data rate is fixed

at 100 baud. See the UCMD command for the PACTOR baud rate threshold settings.

________________________________________________________________________________

PTConn [!]a(aaaaaaa) Immediate Command

Mode: PACTOR Host: PG

_________________________________Parameters_____________________________________

aaaa(aa) is the call sign of the station to be called.

________________________________________________________________________________

PTConn is an immediate command that starts the PACTOR connect protocol. To

start a PACTOR connect, type "PTC" followed by the other station's call sign:

Example: PTC N7ML or, for longpath stations, use the exclamation point

before the call: PTC !N7ML.

As soon as the <CR> is typed, the PK-900 will begin keying your transmitter on

Radio Port 1 with the PACTOR connect sequence.

________________________________________________________________________________

PTHUFF "n" Default 0

Mode: PACTOR Host: PH

_________________________________ Parameters: __________________________________

"n" - 0 to 3 specifies the type of data compression used in PACTOR.

________________________________________________________________________________

To enhance the effective data rate in PACTOR, a data compression scheme may be

automatically enabled. The number "n" corresponds to the type of compression

used, with 0 disabling data compression (default).

When PTH is set to 1, Huffman compression will be used if it is more effective.

The numbers 2 and 3 are reserved for future compression schemes.

Instead of using the normal 8-bit ASCII representation of a character, Huffman

encoding assigns each character a code that may be as few as 2 bits for the most

used characters to as long as 15 bits for the least used characters. For

English (and most other) languages, the use of Huffman compression results in a

smaller number of bits necessary for a given message.

3/93 A-82

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands