Timewave PK-900 Operating Manual Download Page 26

Page: 26 / 392

entering the following after the "cmd:" command mode prompt

will cause the PK-900 to Connect to AAA:

C AAA <Enter>

After a few moments, your monitor should display:

*** CONNECTED to AAA

10. Type HELLO SELF <Enter>

After a few moments, your monitor should echo the same message.

If you have gotten this far then the digital section of the

PK-900 and the VHF packet modem of port 1 are both working.

11. We will now check the PK-900's HF modem. If you are using an

AEA program, follow the instructions to select the HF modem by

turning the VHF Parameter OFF; this will automatically set the

radio baud rate HBAUD to 300 for HF packet work.

If you are using a Computer Terminal or a non-AEA terminal

program, the following sets the HF mode of the PK-900:

Type <CONTROL-C>. (Type C while pressing the <Ctrl> key down.)

Your monitor should respond with the command prompt:

cmd:

Then enter VHF OFF <Enter>

Your monitor should respond with:

Vhf was ON/ON

Vhf now OFF/ON

Then enter HB 300 <Enter>

Your monitor should respond with:

HB was 1200/1200

HB now 300/1200

12. If you are using an AEA program type HELLO SELF <Enter>

Your monitor should soon echo the message you've just typed.

If you are using a Computer Terminal or a non-AEA terminal

program, you must first type CONV or K followed by a <Enter>.

Now you may type a few characters. Your monitor should soon echo

the characters you've just typed.

13. If you are using an AEA program, follow the instructions to

DISCONNECT from a Packet station.

If you are using a Computer Terminal or a non-AEA terminal

program the following will cause the PK-900 to DISCONNECT:

1/93 2-8

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands