Timewave PK-900 Operating Manual Download Page 386 | Manualshive

Page: 386 / 392

background image

14

Section 3

Sound Card Interface Connections for the PK-900/PSK

The Sound Card interface connections are made to the gold connectors labeled “

SOUND

CARD AUDIO

” on the back of the PK-900/PSK. Timewave supplies cables to connect

the sound card to the PK-900/PSK. The cables are supplied with each PK-900/PSK and
upgrade kit. This connection information is provided for the user’s convenience.

PK-900/PSK Connection

TO

To Sound Card Audio input.

INPUT

Insert phone plug into sound card input jack (blue ring around
jack on most sound cards). Use the mic jack input (pink) if
you need more gain.

The phone plug tip and ring are the signal connections. The
tip is the factory default connection. To select the ring use
Jumper JH1 on the Jack PC board mounted on the back panel.

Phone plug sleeve is the signal return connection.

FROM

From Sound Card Audio Ouput (to transmitter audio input)

OUTPUT

Insert phone plug into sound input card jack (green ring
around jack on most sound cards).

The phone plug tip and ring are the signal connections. The
tip is the factory default connection. To select the ring use
Jumper JH2 on the Jack PC board mounted on the back panel.

Phone plug sleeve is the signal return connection.

TO

Plug computer speaker into this jack. It is a parallel connection

SPKRS

to the”

FROM

OUTPUT “

jack, so that you don’t have to have

a separate “Y” connector to plug in your computer speakers.

«
...
384
385
386
387
388
...
»

Summary of Contents for PK-900









































































































































































































































































































































































































Reviews:

No comments

Related manuals for PK-900

Brand: Samson Pages: 92

Brand: Jafar Pages: 10

Brand: NEC Pages: 146

Brand: Canarm Pages: 3

Cutler-Hammer Jockey

Brand: Eaton Pages: 12

Brand: National Instruments Pages: 14

Brand: Nice Pages: 120

Brand: Paradox Pages: 6

Brand: 2gig Technologies Pages: 6

Brand: Securi-Prod Pages: 3

Brand: Z-Wave Pages: 9

Brand: MERCATOR Pages: 4

Brand: W&T Pages: 217

Brand: Danfoss Pages: 4

Brand: OMEGA AIR Pages: 12

Brand: CAME Pages: 28

SatService sat-nms VLC

Brand: Calian Pages: 40

Brand: BLACKMER Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands