Timewave PK-900 Operating Manual Download Page 163

Page: 163 / 392

11.6.3.1 Ending an ARQ PACTOR Contact

When you've finished your "final finals" to the distant station and

both stations are ready to end the PACTOR ARQ contact, you can end

the contact and terminate the link in several different ways:

o Type <CTRL-D> to stop sending after the transmit buffer is empty.

<CTRL-D> breaks the link and returns your PK-900 to Command Mode

in PACTOR Standby. This is the best way to end a PACTOR contact.

o Type <CTRL-F> to stop sending after the transmit buffer is empty,

send your Morse ID and return to PACTOR Standby and Command Mode.

Your PK-900 sends your call sign (in MYCALL) in Morse code, and

then shuts off your transmitter and returns to PACTOR Standby

and Command Mode. This is the best way to end a contact if you

want to identify your station in Morse code as well.

o Wait until all the text has been sent, then type <CTRL-C> to

return to Command Mode, then type "R" to break the link. The

PK-900 will go into the PACTOR Standby mode.

o Type <CTRL-C> to return to Command Mode, then type "R <Enter>

R <Enter>" to break the link immediately! If there are

characters left in the transmit buffer, they will not be sent.

This method should only be used for an emergency shutdown as it

does not send the control signal to the other station that

informs it you are shutting down. As a result, the other station

will continue to send until its internal timer turns it off.

11.6.4 Long Path Contacts

If the station you wish to contact is more than half way around

the world, i.e. a long path station, a special connect command

is used to lengthen the PACTOR timing. In this case, precede the

station's call with the exclamation point:

PTCONN !N7ML <Enter>

If your station doesn't link within a period of time determined

by the ARQTMO command (default 60 seconds), your station will

stop transmitting.

3/93 11-7

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands