Timewave PK-900 Operating Manual Download Page 78

Page: 78 / 392

cmd:CSTATUS S

Ch. A - IO DISCONNECTED

This reminds you that Channel A is your current I/O channel. Any text

that you type in the Converse mode will be sent to channel A on Radio

Port 2. If you had been connected to any other packet stations, the

callsign and channel would have also shown in the display.

Sometimes you might not want to be bothered with anything from the

Radio Port you are not using. For these times either Radio Port may

be turned OFF with the RADIO command. For example, let's say that in

the above example QSO you wanted to work HF packet and did not want to

be interrupted with any VHF connects. Typing the following command

would cause Radio Port 2 to be disabled.

cmd:RADIO /0

RAdio was 1/2

RAdio now 1/0

When a PK-900 Radio Port is disabled, the front panel LCD Status

indicator for that port will be extinguished as a reminder.

4.9 Advanced Packet Operation

Your PK-900 has many commands and features that are not used for

day-to-day connects conversations. Still, as you become more familiar

with packet, some of these features may become important to you.

4.9.1 Transparent Mode

The TRANSPARENT mode allows any 8-bit binary character to be sent by

your packet station. You usually must use the TRANSPARENT mode to

transfer binary and program files to and from other stations.

You can enter the TRANSPARENT mode either by typing TRANS at the cmd:

prompt after you connect, or by setting CONMODE to TRANS. Either way,

once in the transparent mode, any character you type will be sent

automatically after the PACTIME setting. This way the PK-900 can

send any character. We recommend using HARDWARE flow control in

transparent mode but SOFTWARE flow control is available with the

TRFLOW and TXFLOW commands. To get back to Command mode after you are

finished with transparent mode, you must type the COMMAND character

(default <CTRL-C>) 3 times within the "Guard time" set by the

CMDTIME command (default 1 second). (Hold down the CTRL key and press

C three times rapidly.)

4.9.2 Gateway Operation

The PK-900 can allow packet stations on one radio port to communicate

with stations on the other port. When the PK-900 bridges two packet

frequencies in this manner, it is said to be a "Gateway." Gateway

operation is a dual port feature and requires that the correct

port 2 packet modem be loaded. Once this has been done the gateway

function is enabled by entering a callsign in MYGATE. The callsign

must not be the same call sign and SSID as MYCALL or MYMAIL.

1/93 4-36

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands