Timewave PK-900 Operating Manual Download Page 259

Page: 259 / 392

________________________________________________________________________________

PK ["n"] Default: none

Mode: All Host: PK

_________________________________ Parameters: __________________________________

"n" - a hex number used to access the PK-900's memory and I/O locations.

________________________________________________________________________________

PK (Peek/Poke) permits access to memory locations. To use the PK command:

o Set the memory address into the ADDRESS command.

o Use the PK command without arguments to read that memory location.

o Use PK with one argument 0-$FF to write to that memory location.

This command is used as a programmer's aid and is not needed for normal use.

________________________________________________________________________________

PPersist ON|OFF/ON|OFF Default: ON/ON

Mode: Packet, PACTOR Host: PP

_________________________________ Parameters: __________________________________

ON - The PK-900 uses p-persistent CSMA (Carrier Sense Multiple Access).

OFF - The PK-900 uses DWAIT for TAPR-type 1-persistent CSMA.

________________________________________________________________________________

When PPERSIST is ON (default), the PK-900 uses the PERSIST and SLOTTIME

parameters for p-persistent CSMA instead of the older DWAIT CSMA procedure.

PPERSIST may be enabled or disabled on each Radio Port.

When your computer has queued data for transmission, the PK-900 monitors the

DCD signal from its modem. When the channel clears, the PK-900 generates a

random number between 0 and 255. If this number is less-than or equal to

"PERSIST", the PK-900 transmits all frames in its queue. If the random number

is greater than "P", the PK-900 waits .01 * SLOTTIME seconds and repeats the

attempt. PPERSIST can be used in both KISS and normal AX.25 operation.

________________________________________________________________________________

PRType "n" Default: 2 (Epson)

Mode: FAX Host: PY

_________________________________ Parameters: __________________________________

"n" - 0 to 255, specifying a code for dot graphics sequences used in FAX.

________________________________________________________________________________

The following is a list of the different printer graphics types the PK-900

supports the convey the received FAX graphics information to your computer.

PRTYPE Printer PRTYPE Printer

0 Epson 4 IBM

8 Radio Shack (Tandy) 12 Apple (G)

16 Apple (S) 20 old Okidata

24 Okidata 28 Gemini 10, 15

32 Star Micronics 36 GX-100, Gorilla

40 Texas Instruments 44 Genicom

48 Miscellaneous (HP ThinkJet) 52 Citizen

56 NEC 60 Anadex

Unsupported PRTYPE settings are treated as PRTYPE 0.

3/93 A-81

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands