Timewave PK-900 Operating Manual Download Page 54

Page: 54 / 392

The ROUTES command provides routing information about other nodes that

can be reached.

A complete discussion of NET/ROM is beyond the scope of this manual,

but we hope the above information will help get you started.

Certainly the CONNECT, NODES and USERS commands will allow you to

navigate through the network, and find new people to talk to.

4.3.4 Who Can I Talk To?

Now that you understand a little about the different packets and

packet stations, you are ready to make your first real connection.

If you do not have a friend on Packet in your local area, then you

will want to choose a station you can reach. Fortunately the PK-900

has a command called MHEARD that displays the list of the 18 most

recently heard stations. Check this list in one of the following ways:

I If you are using an AEA PAKRATT program, follow the instructions

in the program manual for checking the Packet MHEARD list.

II If you are using a Terminal or Terminal Program on your computer,

then first type a <CTRL-C> to make sure you are in the PK-900

Command (cmd:) mode. Then type the command MHEARD as shown.

You should then see a display similar to the one below.

cmd:MHeard

........ p1 N7GMF

........ p1 K6RFK

........ p1 SEA*

........ p1 N7HWD-8*

........ p1 KD7NM*

........ p1 N7ALW*

........ p1 WA7GCI*

cmd:

The callsigns in the list are the stations heard by your PK-900 with

the most recently heard station at the top of the list. As in the

Monitored packets, the asterisks (*) indicate that the station was

heard directly by the PK-900. The callsigns without an asterisk

were relayed by another station and so cannot be connected to

directly. The "p1" means the station was heard on radio port 1.

4.3.5 Your First Real Connect

Choose one of the stations with an asterisk displayed in YOUR MHEARD

list, or a friend that you know is "on the air" near to you.

If you are using an AEA PAKRATT program, follow the instructions to

CONNECT in Packet mode to the callsign you chose above.

If you are using a Computer Terminal or a non-AEA program, entering

the following after the "cmd:" command mode prompt will cause the

PK-900 to Connect to the station (Callsign) chosen above:

CONNECT (Callsign) <Enter>

1/93 4-12

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands