Timewave PK-900 Operating Manual Download Page 135

Page: 135 / 392

7.9 NAVTEX Operation

NAVTEX is an international system which stands for NAVIGATIONAL TELEX.

It is a direct printing service designed to distribute navigational

and meteorological warnings and other urgent information to ships.

To enter the NAVTEX mode, simply type "NAVTEX" at the command prompt.

The ARRL has also adopted this format for transmitting bulletins. In

amateur radio this same format is starting to be referred to as AMTEX.

AMTEX transmissions can be found on ARRL bulletin frequencies.

NAVTEX is broadcast in Mode-B AMTOR (SITOR) on a frequency of 518 kHz.

NAVTEX may be selectively monitored, so you will see only information

of interest and never see the same message twice. It is this unique

feature of NAVTEX that the PK-900 uses with the NAVSTN and NAVMSG

commands to allow the user to monitor only messages of importance.

NAVTEX/AMTEX messages are prefaced by the characters "ZCZC" and

then a four character Preamble as diagramed below.

ZCZC AA99

||||

|||+-Serial Number 2nd Digit--+

||+--Serial Number 1st Digit--+

|+---Message Classification (A to Z)

+----NAVTEX Station Identification (A to Z)

The first character of the Preamble is a letter that identifies the

NAVTEX transmitter. Transmitter Identification letters can be any of

the characters A through Z. This limits the number of NAVTEX stations

in an area to 26. The NAVSTN Command can be used to selectively

monitor or reject certain NAVTEX transmitters.

The second character of the Preamble is the Message Classification.

The NAVMSG command is used to selectively monitor or reject any of the

NAVTEX message classes shown below:

A. Navigational Warnings

B. Meteorological Warnings (Storm Warnings)

C. Ice Reports

D. Search and Rescue Information

E. Weather Forecasts

F. Pilot Service Messages

G. DECCA System Information

H. LORAN-C System Information

I. Omega Systems Messages

J. SATNAV System Messages

K-Z. Reserved for future use

The exception to this is that message classes A, B and D CANNOT be

excluded and will always be copied if the transmitting station is

enabled by NAVSTN.

The last two numbers form a serial number from 00 through 99 that is

different for each message. The PK-900 remembers the Preamble of

the 200 most recent messages and will not re-print a message that has

the same preamble if it has already been received without many errors.

1/93 7-21

Summary of Contents for PK-900









































































































































































































































































































































































































Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands

Timewave PK-900, Operating Manual

Search results

Summary of Contents for PK-900

Reviews:

Related manuals for PK-900

Brands by name

Popular brands